How to tune d1,d2,d3 params in /etc/disktab

Keith Bostic bostic at ucbvax.BERKELEY.EDU
Tue Sep 27 14:38:37 AEST 1988


For those of you that are interested in maximizing the performance
of your disks, here is an empirical procedure developed by Tom Ferrin
(tef at cgl.ucsf.edu) to tune the drive dependent parameters for 
disk controllers that have search capabilities. CSRG would be
interested in getting experimental results for other drives
in /etc/disktab and also in hearing of refinements to this procedure.


Here is the procedure to empirically determine the correct
drive-dependent parameters for "HP" type disks.  This technique
improved both read and write times for an NEC2362 drive by more
than 2x!  Since the "doubleeagle" params were used as a starting
point, throughput to that drive could probably be improved
considerably as well since the physical characteristics of the
two drives are very similar.  The throughput is now nearly 1MB/sec
on writes (995 KB/s to be exact) and 842 KB/s on reads.

Here is the method:

	0. format the drive and build the badblock table.
	1. set d3 (sdist) to something large, say 20.
	2. set d1 (mindist) to 0.
	3. set d2 (maxdist) to #sectors/track - 1 (63 for the NEC).
	4. write out these parameters using disklabel.
	5. newfs a filesystem and mount it.

This essentially disables the "search" capability of the driver so
than whenever the drive is positioned on the proper cylinder the
driver immediately issues a data xfer command.  This will minimize
the data transfer time at the expense of tying up the controller
for a longer period (possibly for a complete revolution [~17ms]).
Now use Mike's "write_8192" program (was in ~karels/tests on the
distribution tape) to write a 8MB file out to the filesystem.

Optimize maxdist as follows:

	6. use the read_8192 program to determine the real time
	   required to read the data file.  (do 4 - 6 runs to make
	   sure there are no abnormalities on a particular run).
	7. reduce maxdist (d2) by 10 in disktab, write it out with
	   disklabel, and do step #6 again.

The real time required to read the file should remain relatively
constant until maxdist gets too small, then the time will suddenly
jump up as you begin missing revs on the xfer.  Decrease the step
size from 10 to 5 and iterate again, finally choosing a value a
a little larger than the "cut off" value.  (It is much better to
be conservative.)

Optimize mindist by increasing it upwards from 0 using a step size
of 1 or 2, again using read_8192 as the benchmark.  You will see that
time required to read the file will initially be small, but then will
start creeping upwards as the driver begins issuing "search" commands
when it could be starting a read directly.  Back off 1 or 2 sectors
from the point where the file read time first starting increasing.
(Being conservative is less critical here.)

Mindist and maxdist determine the window (measured in sectors) from
which the driver determines to whether to begin a data xfer immediately
or to do a "search" command first (possibly freeing the controller
for a data xfer on another drive).  Values of 2 and 15 worked best for
mindist and maxdist on a NEC D2362, using an Emulex SC7003 controller
on a VAX8650.

Lastly optimize sdist in the same way you optimized maxdist.
A value of 5 is reasonable (far different than the 15 originally found
in disktab).  Again it is better to error on the conservative side, since
being too liberal causes you to miss a rev, while being too conservative
just ties up the controller longer while the data xfer is queued up
and the controller is waiting for the heads to get over the proper sector.

A final note:  bus I/O architecture and CPU speed play a factor in all
of this, since how fast it takes the processor to field a device interrupt
and how fast the code in the driver executes affect timing.  Ideally
someone should use the same drive and controller setup on a slow
CPU (eg VAX750) and see how different the numbers are.



More information about the Comp.unix.wizards mailing list